Warning: Unregistering DLL files is very risky. If you unregister the wrong DLL file, your computer can crash. Back up important files. Set a Restore point
(click Start > All Programs > Accessories >
System Tools > System Restore).

To unregister DLL files, you need to do the following steps:

1. Open a Command Prompt window.
(click Start > Run and type “cmd”)

2. After you have opened a Command Prompt window,
locate the DLL on your pc. ( C:\BadDLLFolder>)

3. Unregister the bad DLL in the BadDLLFolder
( C:\BadDLLFolder>regsvr32 /u Bad.dll)

4. Should get a message of a successful unregistered DLL.

Warning: registering DLL files is very risky.
If you register the wrong DLL file, your computer can crash.
Back up important files.
Set a Restore point
(click Start > All Programs > Accessories >
System Tools > System Restore).

To register DLL files, you need to do the following steps:

1. Open a Command Prompt window.
(click Start > Run and type “cmd”)

2. After you have opened a Command Prompt window,
locate the DLL on your pc. ( C:\GoodDLLFolder>)

3. Register the good DLL in the GoodDLLFolder
( C:\GoodDLLFolder>regsvr32 Good.dll)

4. Should get a message of a successful registered DLL.

If you need to find the lenght of a coax cable then the MFJ-259 will help you find that. You will need to know the velocity factor of the coax cable being measured. Often times this is a know measurement from the manufactor.
Follow the steps below.

1. Short one end of the coax.
2. Connect the other end of the coax to the MFJ-259 input.
3. Turn on the MFJ-259 and start at the lowest frequency range. Watch the RESISTANCE METER for a dip reading (zero ohms) and record the frequency.
4. Continue moving up in frequency to find a second dip, which should be twice the first (recorded) dip frequency.
5. Calculate the length: Divide 492 by the first dip frequency (in MHz) and multiply the result by the velocity factor of the coax cable being measured. The result should be in feet.

If you need to find the bad spot (short) of a coax cable then the MFJ-259 will help you find that. You will need to know the velocity factor of the coax cable being measured. Often times this is a know measurement from the manufactor.
Follow the steps below.

1. Connect the coax to the MFJ-259 input.
2. Turn on the MFJ-259 and start at the lowest frequency range. Watch the RESISTANCE METER for a dip reading (zero ohms) and record the frequency.
3. Continue moving up in frequency to find a second dip, which should be twice the first (recorded) dip frequency.
4. Calculate the position of the short: Divide 492 by the first dip frequency (in MHz) and multiply the result by the velocity factor of the coax cable being measured. The result should be
in feet.

If you need to find the velocity factor of a coax cable manually then the MFJ-259 will help you find that. You will need to have a piece of coax of a know length/measurement
Follow the steps below.

1. Disconnect both ends of the coax and measure the physical length of the line in feet.
2. Find the lowest frequency across all the bands at which the lowest SWR occurs.
3. Read the frequency from the frequency counter display. This is the 1/4 resonant wavelength frequency of your coax. Note that you will get low SWR reading at all odd multiples of 1/4 wavelength.
Example: On a 27 foot line the measured frequency was 7.3MHz.
4. Divide 246 by the measured frequency. This gives you the free space 1/4 wavelength in feet.
Example: 246 divided by a dip frequency of 7.3 MHz is 33.7 feet, the free space 1/4 wavelength
5. Divide the physical measured length of the coax in feet by the free space 1/4 wavelength calculated in number 4.
Example: 27 feet (physical length) divided by 33.7 feet (calculated length) equals .80 . The velocity factor is .80 or 80%.

Free space 1/4 wavelength = 246 / Low SWR frequency
Velocity Factor = Actual feedline length / Free space 1/4 wavelength